28C64 DATASHEET PDF

28C64 DATASHEET PDF

AT28C64, 28C64 Datasheet, 28C64 64K ns Parallel PLCC EEPROM Datasheet, buy 28C 28C64 datasheet, 28C64 pdf, 28C64 data sheet, datasheet, data sheet, pdf, Atmel, 64K 8K x 8 CMOS E2PROM. 28C64 64K (8K x 8) CMOS E2prom with Page Write and Software Data Protection Features. Fast Read Access Time ns Automatic Page Write Operation.

Author: Jucage Akinozuru
Country: Jordan
Language: English (Spanish)
Genre: Photos
Published (Last): 6 September 2016
Pages: 167
PDF File Size: 15.28 Mb
ePub File Size: 9.85 Mb
ISBN: 523-6-97876-750-9
Downloads: 28341
Price: Free* [*Free Regsitration Required]
Uploader: JoJozuru

The same diagram shows CE being asserted followed by OE for a read cycle. Here is my code, sorry if it seems too cluttered: That might help things. Post as a guest Name.

I have edited my question. Since I am only using the first three address pins, the rest are tied low. Also, I would suggest that you should write a writebyte procedure which sets all address and data wires to output and puts proper values on them, ensures WE and OE are deasserted, asserts CE, asserts and release WE, and releases CE, and a readbyte procedure which sets all address wires to output and puts proper values on them, sets all data wires to input, asserts CE and OE, samples all the data wires, and releases CE and OE.

One thing that datahseet missing datashset on page 7 of the datasheet, it states that you need to write a sequence of codes to disable dztasheet. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

Mar 26 ’13 at I’d recommend following that same sequence and also change your write sequence to follow the diagram on the following page. That will make the remainder of your code much more readable. If it has, you’ll need to wire up all your address wires in order to disable it. Thanks for the info. I have tested an earlier version of the above program with a static RAM chip and everything works great.

  BIOTRANSFORMATION DES TOXIQUES PDF

I don’t really like the design, but my guess is that it was trying to be compatible with an earlier part where one could write locations one at a time and just wait after each one. Home Questions Tags Users Unanswered.

Here is the serial output. Looking at the datasheet on page 12 it shows a timing diagram and Chip Enable Access Time can be up to nS.

28C64 EEPROM Programming Using Arduino – Electrical Engineering Stack Exchange

Any help would be much appreciated. BTW, if the chips are equipment pulls as opposed to new parts, it’s possible that the “software protection” feature has previously ratasheet enabled.

Email Required, but never shown. Sign up or log in Sign up using Google. Here is my code, sorry if it seems too cluttered:. The chips are new, and I actually have two from two different manufacturers.

Sign up using Facebook. I am using the Xicor 28C64AP xatasheet datasheet. I understand the benefits of separating the code into subroutines and will probably do this, but for now I am just trying to get the byte write working.

28C64A-15 – 28C64A 64K 150ns Parallel EEPROM Technical Data

Sign up using Email and Password. Thanks for the response, supercat.

  JOSEF PIEPER LEISURE THE BASIS OF CULTURE PDF

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these 2864.

I added ms delays between every control pin change and made sure the order was consistent with the datasheet, but still no luck. When the timer datssheet, an internal write cycle is triggered and additional writes before it completes. I wrote a program for the Arduino Uno that writes data to the first 4 addresses and then reads the data back. All behave datasheeet same. You have not indicated that you are doing anything with them?

The timings for this particular EEPROM aren’t super-critical, but it has a timer which starts when the first byte is written and gets reset if another byte is written before it expires.

28C64 Datasheet PDF –

The device has 13 address pins, which should specify an address in binary from 0x to 0x1FFF. Initializing pins for write I have tied the top 10 address bits low and am only using the first 3 for now. Mar 27 ’13 at By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. PeterJ 16k 20 42