HT12E DATASHEET IN PDF

HT12E DATASHEET IN PDF

The capability to select a TE trigger on the HT12E or a DATA trigger on the HT12A further enhances the application flexibility of the 2 12 series of encoders. HT12E Datasheet, HT12E Holtek Encoder Datasheet, buy HT12E Encoder IC. The capa- bility to select a TE trigger on the HT12E or a. DATA trigger on the HT12A/B/C further en- hances the application flexibility of the 2.

Author: Faezuru Dailmaran
Country: Laos
Language: English (Spanish)
Genre: Technology
Published (Last): 24 March 2005
Pages: 63
PDF File Size: 18.80 Mb
ePub File Size: 4.31 Mb
ISBN: 682-3-54526-755-7
Downloads: 65690
Price: Free* [*Free Regsitration Required]
Uploader: Mejora

The IC is has a wide range of operating voltage from 2. The encoded bit can be obtained from the Dout pin pin This cycle is repeated as long as TE is kept low. HT12E is an encoder integrated circuit of 2 12 series of encoders. These are the 8-bit address bits, which is used to protect your data.

Pull the Transmission Enable pin pin 14 to ground to activate transmission. HT12E has a transmission enable pin which is active low. Simply put, HT12E converts the parallel inputs into serial output. SPI Hf12e of Arduino.

So out of the bits 8-bits will be used to set address and the remaining 4-bit will dataheet used to transmit data. It encodes the 12 bit parallel data into serial for transmission through an RF transmitter. In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.

These 12 bits are divided into 8 address bits and 4 data bits. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

  COBEN BLEKITNA KREW PDF

TL — Programmable Reference Voltage. They can also be connected to switches to manually send and receive data. The IC has a built in oscillator. Interface GPS with Arduino. Choosing Battery for Robots.

HT12E Encoder IC | HT12E Datasheet | Pin Diagram & Description

Transmission enable; active low. If you want security you can connect any of the 8 pins to 5V to make it high.

These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits. This oscillator can be used by connecting these two pins through a 1M Resistor. Choosing Motor For Robots. HT12E begins a 4-word transmission cycle upon receipt of a transmission enable. This pin has to be connected to Ground 0V to enable the Transmission. Can range from 2. The primary function of HT12E is to encode a bit and send it out through the output pin.

The Encoded 12 bit output data can be obtained from this pin. Virgin Galactic — Commercial Space Flight. As soon as TE returns to high, the encoder output completes its final cycle and then stops. Arduino based GPS receiver. It is very important that your Decoder should also have this same address for them to talk to each other.

In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. Supply voltage; 5V 2.

  JURNAL CACING TREMATODA PDF

Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. You can know to set up the HT12D after this from here. This high-density System-in-Package SiP integrates controller, power switches, and support components. They are paired with 2 12 series un decoders for use in remote control system applications.

HT12E Encoder IC

Submitted by admin on 30 October So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited datasheef you. The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7.

Skip to main content. Interface SD Card with Arduino.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. It is mainly used in interfacing RF and infrared circuits.

A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to dxtasheet. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built. What is Web Browser. These two ICs together form an Encoder and Decoder pair.

Connected to the Ground of circuit.